10 best smoke detector photoelectric kidde for 2022
It took days of going through more than a thousand customer reviews and conducting expert researches to narrow down the list. Weve included a comparison table below to give you a quick summary of our top 10 smoke detector photoelectric kidde. Its followed by an in-depth review of each smoke detector photoelectric kidde. Hopefully, once you are done reading this article, you will be well informed about smoke detector photoelectric kidde and be able to select the right smoke detector photoelectric kidde for you without any hesitations.
Best smoke detector photoelectric kidde
1. Kidde Smoke and Carbon Monoxide Detector Alarm with Voice Warning | Hardwired w/Battery Backup | Interconnectable | Model # KN-COSM-IBA
Feature
Smart Interconnect-Interconnects up to 24 Kidde devices (of which 18 can be initiating), Battery Backup (2-AA batteries included)-Provides protection during power outages.Front Loading Battery Door-Replace the backup batteries without disconnecting from mounting bracketHumidity range:10%-95% relative humidity, non-condensing.Battery Lockout System-The battery door will not close unless the batteries are properly installed, Alarm Tamper Resist-Helps deter from tampering and theft, Adjustable Mounting Bracket-Makes installation fast and easy. Works with existing smoke and combination smoke and CO mounting brackets.
Peak Level Memory-Announces "CARBON MONOXIDE PREVIOUSLY DETECTED" if alarm has detected a CO level of 100ppm or higher since it was last reset, HushTM Feature-Silences nuisance alarms for approximately 9 minutes. (Smoke must be present before HushTM is activated)
Ionization Sensor Technology-Ideal for detecting fast flaming and other types of fires, est Button Functions:- Tests the unit for proper operation - Peak Level memory - Resets the Carbon Monoxide alarm
Green LED-Illuminates to indicate the unit is receiving AC power. Flashes once every 60 seconds to indicate battery only mode. Flashes once per second during alarm to indicate initiating alarm. Flashes once every 16 seconds to indicate smoke or CO previously detected. Flashes every 2 seconds while the alarm is in HUSHTM mode
Red LED-When a dangerous level of smoke or carbon monoxide is detected the red LED will flash. If the unit malfunctions, the red LED will flash and the unit will chirp every 30 seconds
Talking alarm announces the hazard type detected, helping to speed up reaction time
Combined carbon monoxide and smoke alarm, a single unit can be installed where previously two were needed
Battery safeguard ensures the unit cannot be accidentally mounted without batteries
Test-reset button tests alarm circuitry and triggers the voice announcement
Meets safety standards set by Underwriters Laboratories (UL) and interconnects with other KN-COSM-IBA models
120V AC, All Kidde brand hard wired smoke alarms are interconnectable with the KN-COSM-IBA
Description
This combination smoke/CO alarm features an 85dB horn and voice that announces "Fire", "Carbon Monoxide", and "Low Battery" warnings when detected. It can also interface with other Kidde interconnectable alarms. Meets NFPA 72 standards Smoke and Carbon Monoxide Alarm, Detection Method Ionization, Electrochemical, Up to 24 Units Interconnection Capability, Power Source 120VAC, 9V, Audible Alert 85dB @ 10 ft., Horn, Visual Alert Red LED, Diameter 5-3/4 In., Height 1-3/4 In., Digital Readout No, Battery Backup Yes, Features Voice Warning, Peak Level Memory, Reset Button, Hush Button Yes, Locking Pin Yes, Operating Temp. 40 Degrees to 100 Degrees F, Standards UL, Includes Mounting Anchors and Screws2. Kidde Safety - 21026055 Kidde Sealed Lithium Battery Power Smoke Detector Alarm | Model i9010,White
Feature
Sealed-In Lithium Battery - Sealed-in lithium power supply; no battery replacement required over the 10 year life of the alarm. Eliminates worry about battery removal or unauthorized deactivation of alarmSelf Activation - Alarm automatically activates when attached to the mounting bracket, HushTM - Will temporarily silence nuisance alarms and will not allow hush mode to be activated unless the unit is in alarm mode
Alarm Memory - Rapidly flashing LED alerts user if the alarm has sounded since the last time the test/reset button was used
End of Life Warning - Alarm chirps every 40-45 seconds indicating the alarm is in need of replacement, Tamper Resist - (when activated upon installation) effective in preventing someone from removing the unit from the mounting bracket
Test/Reset Button - Tests unit's circuit operation and resets memory after an alarm condition occurs, LED - A flashing red indicator light with four modes of operation: standby, alarm mode, hush mode, and memory set
Sealed in lithium battery never replace battery over the ten-year life of the alarm
Self activation alarm automatically activates when securely attached to the mounting bracket
Smart hush temporarily silences nuisance alarms and will not allow hush mode to be activated unless the unit is in alarm mode
Rapidly flashing red LED alerts the user if the alarm has sounded since the last time the test reset button was used
Kidde?s smoke alarms meet the requirements of Underwriters Laboratories (UL), an independent facility that tests products for compliance with widely-accepted safety standards
Description
No need to worry about faulty batteries with the Kidde i0910 10-Year Sealed Lithium Battery-Operated Smoke Alarm. This worry-free alarm contains a sealed-in lithium power supply that lasts the lifetime of the unit. Dependable and easy to install, this no-maintenance alarm saves on labor and battery costs over its lifetime. Save up to $60 in Battery Replacement Costs This worry-free smoke alarm can save you a lot of time and money over its lifetime (an estimated $60 over the 10 year life of the alarm). This alarm can save you--and the local landfill--from the cost, hassle, and waste of lots of batteries. This smoke alarm is also a great choice for hallways and high ceilings, where changing batteries can be especially difficult. Never Replace a Battery Again. View the 10-year worry-free smoke alarm. i4618 Never change a battery again. The Kidde Sealed Lithium Smoke Alarm saves you up to $60 and eliminates battery replacement hassles. Product Highlights No battery replacement for the lifetime of the alarm Powered by a tamper-free sealed lithium power supply Self-Activation automatically activates unit when attached to bracket Smart Hush silences alarm in non emergencies Money-saving alarm is great for homes and rental properties This alarm uses ionization sensing technology for the smoke alarm. Ionization sensing alarms may detect invisible fire particles (associated with flaming fires) sooner than photoelectric alarms. Photoelectric sensing alarms may detect visible particles (associated with smoldering fires) sooner than ionization alarms. Kidde strongly recommends that both ionization and photoelectric smoke alarms be installed to help insure maximum detection of the various types of fire that can occur within the home. Great for Homes and Rental Properties This tamper-free alarm prevents battery or alarm removal, eliminating worry about unauthorized battery removal or unauthorized deactivation of the alarm. Also, this alarm is a good choice for rental properties and high-density dwellings, as its sealed tamper-free design prevents theft, while also reducing labor and material costs. This helps to ensure that the property and inhabitants are protected by a fully operational alarm. Easy to Install with Self Activation The innovative automatic activation of this alarm is unlike any other smoke alarm design. The alarm will automatically activate when it is attached to the mounting bracket; there are no pull tabs and no switches--everything is automatic. At the end of the alarm life, the unit will chirp, indicating the alarm is in need of replacement. You can use a simple tool, such as a screwdriver, to deactivate the unit, stopping the low-battery chirp and making the alarm safe for disposal. The sealed-in board-mounted batteries will power the unit for its complete 10-year life. No replacement batteries will ever be needed. Trademarked Hush Feature for Convenience By pressing the smoke alarm's Hush button, you can easily and safely silence nuisance alarms caused by non-emergency situations, such as overcooked dinners. This alarm's Smart Hush feature has the capability of temporarily desensitizing the alarm circuit for up to eight minutes. This feature is to be used only when a known alarm condition, such as smoke from cooking, activates the alarm. The smoke alarm is desensitized by pushing the Test/Hush button on the smoke alarm cover. If the smoke is not too dense, the alarm will silence immediately. The red LED will illuminate for 1.5 seconds every eight seconds while in Hush mode. This indicates that the alarm is in a temporarily desensitized condition. Additionally, the smoke alarm will automatically reset after approximately eight minutes and sound the alarm if particles of combustion are still present. Smart Hush can be used repeatedly until the air has been cleared of the condition causing the alarm. Pushing the Test/Hush button on the alarm will end the hush period. Power Outage Protection, Indicator LED, and Test Feature A 10-year sealed lithium battery powers this alarm, providing continuous protection against smoke and fire hazards even during power outages. Because a smoke alarm only helps protect you if it's working, this unit features a red LED that flashes every 40 to 45 seconds to indicate that it is operating correctly. For additional peace of mind, the alarm contains a Test/Reset button that enables you to periodically test its circuitry and horn. The unit measures just 5.6 inches in diameter and 1.5 inches in depth, and it features a neutral, white finish. This smoke alarm is UL listed, so you can be confident of its quality, and it is backed by a 10-year limited warranty. About Kidde: A UTC Fire & Security Brand Renowned for global leadership in fire detection and suppression, Kidde provides solutions ranging from portable fire extinguishers to advanced industrial controls, such as flame detection and explosion-suppression systems. Kidde is a UTC Fire & Security brand, with a history that's rich with innovations, from the patent of the Chubb Detector Lock in 1818 to the development of the world's first wireless networked smoke detectors in 2004. What's in the Box Kidde i0910 10-Year Sealed Lithium Battery-Operated Smoke Alarm with mounting bracket and hardware, 10-year limited warranty, and bilingual user's manual.3. Kidde 21007624 AC Photoelectric Smoke and Carbon Monoxide Detector Alarm | Hardwired with Battery Backup | Model # KN-COPE-IC
Feature
Provides protection from fire and carbon monoxide in one unit with Photoelectric sensor.Fire Warning - The red LED will flash and be accompanied by three long alarm beeps followed by a verbal warning message "FIRE! FIRE!". The alarm will repeat pattern until unit is reset or smoke is eliminated.
Carbon Monoxide Warning - Four short alarm beeps followed by a verbal warning "WARNING! CARBON MONOXIDE!" This continues until the unit is reset or the CO is eliminated.
Low Battery Warning - One chirp followed by warning "LOW BATTERY". The red LED light will flash. This pattern will continue every minute for the first hour. After the first hour the red LED light will flash once every minute accompanied by the chirp sound. The "LOW BATTERY" warning will only sound once every fifteen minutes. Voice Hush Indication: "HUSH ACTIVATED" and "HUSH CANCELLED" voice announcement
Alarm Memory - The green LED will blink once every 16 seconds to alert a user when the unit has alarmed for smoke or has detected a concentration of CO. If the alarm has detected a CO level of 100ppm or greater, when the Test/Reset button is pressed the unit will announce "CO PREVIOUSLY DETECTED". If the alarm has detected abnormal levels of smoke since its last test, it will produce three rapid beeps.
AC-Wire with battery backup, An included 9V battery protects during short-term power outages
Front-loading battery with unique battery door design
Voice Warning with Green and Red LEDs
Photoelectric smoke sensor - May detect visible fire particles associated with slow smoldering fires sooner than an ionization sensor.
Tamper resistant
Description
The Kidde Front-Loading Smoke and Carbon Monoxide alarm (part # 21007624) offers protection from two hazards fire and CO in one unit. Sold under the FireX brand, this AC-wire with battery backup alarm emits a beeping tone followed by a voice warning that clearly announces the danger by saying, Fire! Fire! or Warning! Carbon Monoxide!. The uniquely designed frontloading battery compartment makes battery replacement quick and easy, and ensures proper installation. Manufactured with photoelectric sensors for detecting smoke and fire, this alarm also includes the worlds most accurate CO sensing technology based on claims by major manufacturers. Architectural and Engineering Specifications - The combination smoke and carbon monoxide alarm shall be Kidde Unit Number KN-COPE-I (part number 900-0213) or approved equal. It shall be powered by 120VAC, 60Hz source with a 9V battery backup. The temperature operating range shall be between 40F and 100F (4C and 38C) and the humidity operating range shall be 5% - 85% relative humidity. The unit shall incorporate a photoelectric smoke sensor with nominal sensitivity of 2.05%/ft. The CO sensor shall be of a fuel cell design and shall meet the sensitivity requirements of Underwriters Laboratories UL2034 Single and Multiple Station Carbon Monoxide Detectors. The unit shall qualify for UL-approved wording on the package: Worlds Most Accurate Carbon Monoxide Alarm*. The combination alarm can be installed on the surface of any wall or ceiling following the UL/NFPA/Manufacturers recommended placement guidelines. The alarm can be installed on any standard single gang electrical box, up to a 4octagon junction box. The electrical connection (to the alarm) shall be made with a plug-in connector. The unit shall provide optional tamper resistance that deters removal of the unit from the wall or ceiling. No additional pieces shall be required to activate this feature. A maximum of 24 Kidde devices can be interconnected in a multiple station arrangement. The interconnect system must not exceed the NFPA (National Fire Protection Association) limit of 18 initiating devices, of which 12 can be smoke alarms. With 18 initiating devices (smoke, heat, CO, etc), interconnected, it is still possible to interconnect 6 strobe lights and or relay modules. The alarm shall include a test button that will electronically simulate the presence of smoke and CO and cause the unit to go into both modes of alarm. This sequence tests the units electronics to ensure proper operation. The CO sensor will not alarm to levels of CO below 30 ppm and will alarm in the following time range when exposed to the corresponding levels of CO. 70 ppm CO Concentration 60 240 minutes 150 ppm CO Concentration 10 50 minutes 400 ppm CO Concentration 4 15 minutes The combination alarm shall have two methods of warning for danger: a piezoelectric horn that is rated at 85 decibels at 10 feet and a voice warning that identifies the danger. For a CO incident, the horn will sound in the repetitive manner four (4) fast beeps, a short pause, four (4) fast beeps, a short pause. In between, the unit will announce Warning Carbon Monoxide! In a Smoke incident, the horn will sound in the repetitive manner three (3) beeps, a pause, three (3) beeps, a pause. In between, the unit will announce Fire! Fire! The unit shall incorporate 2 LEDs. A green LED will be steady on when AC power is present, flash every 30 seconds when in thebattery only mode, every 16 seconds to indicate alarm memory, and every 2 seconds to indicate the Hush mode is active. A red LED will flash in unison with the sounder pattern. The unit shall include the Smart Hush feature that silences the unit for approximately 8 minutes if a nuisance alarm condition occurs. The Green LED on the alarm will flash every 2 seconds while in Smart Hush and will automatically reset itself. It also provides voice annunciation of Hush Activated when Smart Hush is activated and Hush Cancelled when the Hush cycle ends. The unit shall also indicate a low battery warning utilizing each of the following methods: a brief alarm chirp, the voice announcement of Low Battery! The unit shall at a minimum meet the requirements of UL 2034, UL217, NFPA72, (chapter 11 2002 edition) The State of California Fire Marshall, NFPA101 (One and two family dwellings) Federal Housing Authority (FHA), Housing and Urban Development (HUD). It shall also include a 10-year manufacturers limited warranty. *Claim approved by UL, based on manufacturers reported testing.4. Kidde 21010170 10 Year Smoke and Carbon Monoxide Alarm Detector | Photoelectric | Kitchen | Model P3010K-CO
Feature
Ideal for the kitchen with 10-year sealed lithium battery and smoke and CO sensing technologies work together to detect real fires faster and reduce cooking-related nuisance alarmsHassle-free protection - Goodbye late night low battery chirps! Never replace a battery during the alarm's operating life and no need to worry about the batteries being removed
Always on - Sealed-in lithium battery powers alarm for 10 years - the life of the alarm.
The right alarm, the right location. - Each of the four smoke alarms includes features designed to address location-specific safety needs, such as an LED light in the hallway.
Combination Smoke and Carbon Monoxide Alarm - Smoke and CO sensing technologies work together to detect real fires faster and reduce cooking-related nuisance alarms.
Description
The Kidde P3010K-CO is a 10-year, sealed battery, smoke and carbon monoxide alarm that features photoelectric and electrochemical sensing technology with Smart Hush feature. This combination alarm combines the detection capabilities of a photoelectric sensor with that of an electrochemical sensor, which is used to detect CO. When either sensor notices a potential hazard, it will communicate with the other. Depending on what is detected, the alarm will adjust its smoke sensitivity in order to better discriminate between a real hazard and a false one. This constant communication enhances the alarms overall performance and significantly reduces the potential for a nuisance alarm. The sealed in lithium battery will power the unit for the entirety of its 10 year life, eliminating the need for battery replacement and worry about unauthorized battery removal. The alarm provides continuous protection from smoke and carbon monoxide, even during power outages. The alarm will automatically activate when it is attached to the mounting bracket; there are no pull-tabs, no switches, everything is automatic. At the end of alarm life, the unit will chirp, indicating the alarm is in need of replacement. The customer can use a simple tool such as a screwdriver to deactivate the unit, stopping the chirp and making it safe for disposal. Industry experts (such as the NFPA), recommend that both ionization and photoelectric smoke alarms be installed to help insure maximum detection of the various types of fires that can occur within the home. Ionization sensing alarms may detect invisible fire particles (associated with fast flaming fires) sooner than photoelectric alarms. Photoelectric sensing alarms may detect visible fire particles (associated with slow smoldering fires) sooner than ionization alarms. Kidde Worry-Free Kitchen Smoke & Carbon Monoxide Alarm Part Number(Ordering Number):210096675. Kidde 21006371 p12040 Hardwire with Battery Backup Photoelectric Smoke Alarm, White
Feature
LED - Red LED indicates that the smoke alarm is operating properly, HushTM, and alarm condition. Green LED indicates the presence of AC powerPhotoelectric Sensor - Advanced photoelectric sensor may detect visible particles (associated with smoldering fires) sooner than ionization alarms. Dust cover protects sensor during construction
Battery Backup (9V Battery Included) - Provides continuous protection even during power outages. Battery Pull Tab eliminates battery installation time and keeps battery fresh
Test Button - Tests unit's electronic circuitry, horn and battery function
Quick Connect Power Harness - Makes installation fast and easy
Description
The Kidde P12040 is a 120VAC powered photoelectric smoke alarm with 9V battery back up. This advanced smoke alarm has the ability to function as a stand-alone unit or in an interconnected system. The Kidde P12040 includes a test button, quick-connect power harness and offers a 10-year limited warranty. This alarm uses photoelectric sensing technology. Photoelectric sensing alarms may detect visible particles (associated with smoldering fires) sooner than ionization alarms. Ionization sensing alarms may detect invisible fire particles (associated with flaming fires) sooner that photoelectric alarms. Kidde strongly recommends that both ionization and photoelectric smoke alarms be installed to help insure maximum detection of the various types of fire that can occur within the home. The Kidde model P12040 is a 120VAC powered alarm that includes a 9V battery backup to provide continuous protection during a power failure and included a quick connect power harness to make installation simple. Part Number (Ordering Number): 21006371 Architectural and Engineering Specifications - The smoke alarm shall be Kidde model P12040 or approved equal. It shall be powered by a 120VAC, 60Hz, 80mA source along with a 9V battery back up. The unit shall incorporate a photoelectric sensor with nominal sensitivity of 1.20%/ft to 3.36%/ft. The temperature operation range shall be between 40F and 100F (4C and 38C) and the humidity operation range shall be 5% - 95% relative humidity. The smoke alarm can be installed on any standard single gang electrical box, up to a 4 octagon junction box. The electrical connection (to the alarm) shall be made with a plug-in connector. A maximum of 24 Kidde devices can be interconnected in a multiple station arrangement. The interconnect system must not exceed the NFPA (National Fire Protection Association) limit of 18 initiating devices, of which 12 can be smoke alarms. With 18 initiation devices (smoke, heat, CO, etc.), interconnected, it is still possible to interconnect 6 strobe lights and or relay modules. The unit shall provide optional tamper resistance that deters removal of the unit from the wall or ceiling. The alarm shall include a test button that will electronically simulate the presence of smoke and cause the unit to go into alarm. This sequence tests the units electronics, battery and horn to ensure proper operation. The unit shall include a piezoelectric horn that is rated at 85dB at 10 feet. The unit shall also include a low battery warning utilizing a brief alarm chirp every 30-40 seconds for a minimum of seven (7) days. The unit shall incorporate one red LED to indicate the alarms current status and mode of operation. The red LED will indicate one of two conditions: Standby Condition: The red LED will flash every 30-40 seconds to indicate that the smoke alarm is operating properly. Alarm Condition: When the alarm senses products of combustion and goes into alarm, the red LED will flash rapidly (one flash per second). The rapid flashing LED and pulsating alarm will continue until the air is cleared. The unit shall incorporate one green LED to indicate the presence of AC power. The unit shall at a minimum meet the requirements of UL217, NFPA72, The State of California Fire Marshall, NFPA 101 (One and two family dwellings) Federal Housing Authority (FHA), Housing and Urban Development (HUD). It shall also include a 10-year manufactures limited warranty.6. Kidde PE9 (P9050) Battery-Operated Photoelectric Sensor Smoke Alarm
Feature
Advanced photoelectric sensor is especially effective in detecting smoldering firesBattery backup 9V battery included (best with Polaroid 9 Volt batteries)
Battery pull tab eliminates battery installation time and keeps battery fresh
Quick connect power harness makes installation fast and easy
Kiddes smoke alarms meet the requirements of Underwriters Laboratories (UL), an independent facility that tests products for compliance with widely-accepted safety standards
7. Kidde 21026065 Smoke & Carbon Monoxide Alarm with Voice Warning
Feature
Combination Smoke and Carbon Monoxide Alarm Smoke and CO sensing technologies work together to detect real fires faster and reduce nuisance alarms.Voice Alarm Announces the hazard type detected thereby helping to speed up the correct reaction. Alarm announces Fire! when a smoke or fire hazard is detected and announces Warning Carbon Monoxide when a CO hazard is detected.
Sealed-In Lithium Battery Sealed-in lithium power supply; no battery replacement required over the 10 year life of the alarm. Eliminates worry about battery removal or unauthorized deactivation of alarm.
Photoelectric Sensor Smoke alarm contains advanced photoelectric sensor that may detect visible particles (associated with smoldering fires) sooner than ionization alarms.
Self Activation Alarm automatically activates when attached to the mounting bracket.
8. Kidde Worry-Free Smoke Alarm, 2 pk.
Feature
Install these Kidde Worry-Free Smoke Alarms to provide your home with reliable protection against smoke and fire. The alarms are equipped with sealed-in lithium batteries that are designed to last for the life of the alarms. Photoelectric sensors can detect fire particles, which are associated with slow, smoldering fires, quickly. Once the alarms are attached to the mounting brackets, they activate automatically for simple use. Product Features: Provides reliable protection Sealed-in lithium b9. Kidde 21028499 DC Smoke and Carbon Monoxide Alarm Detector with TruSense Technology | Front Load Battery | Voice Notification | Model 2070-VDSCR, White
Feature
Multi Criteria Optical Sensor: Detects more types of fires and reduces cooking nuisance alarms.Electrochemical CO Sensor: Protects against dangerous levels of carbon monoxide.
Voice Notifications: Unit verbally announces alerts such as "Fire! , " "Warning, Carbon Monoxide, " and "Low Battery", which helps the user better understand current status of the unit.
Front Loading Battery Door: Quickly change the battery without removing the alarm from the mounting bracket
Three Color LEDs: provide visual notifications of alarm status. Temperature Range: 40F (4.4C) to 100F (37.8C)
10. Kidde 21028502 AC/DC Wire-in Smoke Alarm Detector with TruSense Technology | Front Load Battery Backup | Voice Notification | Model 2070-VASR, White
Feature
Multi Criteria Optical Sensor: Detects more types of fires and reduces cooking nuisance alarms.Front Loading Battery Door: Quickly change the battery without removing the alarm from the mounting bracket
Voice Notifications: Unit verbally announces alerts such as Fire! and Low Battery, which helps the user better understand current status of the unit.
Three Color LEDs: provide visual notifications of alarm status
Recent Comments