Best arduino led driver shield for 2022
When it comes to choosing your arduino led driver shield, there are hundreds of different choices. In our review, weve considered all the various features youll need to know before buying the best arduino led driver shield. We hope that through this article, with our comparison table, in-detail review of each product can help you decide which one is your best arduino led driver shield.
Best arduino led driver shield
1. Adafruit 16-Channel 12-bit PWM/Servo Shield - I2C interface -
Feature
There's an I2C-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running!It is 5V compliant, which means you can control it from a 3.3V Arduino and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
6 address select pins so you can stack up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs
Adjustable frequency PWM up to about 1.6 KHz
12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
2. SunFounder Full Color RGB LED Matrix Driver Shield + RGB Matrix Screen for Arduino
Feature
A simplified version of Colordruino: functions just like the Colorduino, except that it's not supporting cascading; code completely compatible. Just plug the module onto a R3 board (for Arduino, SunFounder, or other compatibles) for useUse DM163 as the driver chip on the driver shield; just plug the 8x8 LED dot matrix screen on the shield for use; support at most 256 x 256 x 256 = 16,777,216 colors
Support display of both the three primary colors, red, green, blue, separately and their mixed colors
Module size: 64.3 x 35.0 x 26.5mmWorking current: 300mA; operating temperature range: -1050
Working voltage: 5V DC; PCB size: 6.0 x 6.0 cm. For more info, please refer to http://wiki.sunfounder.cc/index.php?title=Full_Color_RGB_LED_Matrix_Driver_Shield_%2B_RGB_Matrix_Screen
3. DFRobot RGB LED Strip Driver Shield v1.0
Feature
Compatible with Arduino Uno, Mega, Romeo, etcCompatible with 12V RGB LED Strip(Common Anode)
Recommend working power: 72W (2A per way)
Limited driving capability: 10 meter RGB LED Strip with max brightness
Support IR remote control. Any technical issues after purchase please contact with our tech-support team: [email protected]. Product wiki >>> https://wiki.dfrobot.com/RGB_LED_Strip_Driver_Shield_SKU%EF%BC%9ADFR0274
4. HiLetgo PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
Feature
Communication Interface: IIC16-way steering gear control
Voltage: DC5-10V power supply
The PCA9685 chip is wrapped in the center of the board
All PWM output lines have a 220 ohm series resistor protection and can easily drive LED
5. 16 Channel PWM/Servo Driver IIC interface-PCA9685 for arduino or Raspberry pi shield module servo shield
Feature
It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs
Adjustable frequency PWM up to about 1.6 KHz;Configurable push-pull or open-drain outputManufacturer
12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
We are the owner of Brand"FICBOX",Customer Services is Valid for Purchasing from "FicBox Direct" ONLY
6. 0.8A Bi-directional dual channel DC Motor Driver L298P Shield for Arduino, 5-26V
Feature
Logic control, 5V from Arduino main boardbi-directional control of two DC brush motor
Motor Driven Voltage?6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
Up to 2A current each channel
Pin 4, 5,6,7 are used to drive two DC motor
7. Cytron 10A Bi-directional DC Motor Driver Shield for Arduino, 7v-30v, peak 15A
Feature
Bi-directional control for 1 brushed DC motor.Support motor voltage ranges from 7V to 30V (Rev2.0).
Maximum current up to 10A continuous and 15A peak (10 seconds).
3.3V and 5V logic level input.
Fully NMOS H-Bridge for better efficiency and no heat sink is required.
8. MOS FET PWM 3-20V to 3.7-27VDC 10A 4-Channel Driver Module PLC Amplifier Circuit Board
Feature
STABLE PERFORMANCEThe driver module using high quality ultra-small optocoupler, with strong anti-interference ability, and stable performance, is complete isolation of input signal and output.PWMThe driver module can input PWM to control motor speed, lamp brightness and so on.
INDICATOR LIGHTThe PLC amplifier circuit board with input and output signal indicator.
WIDE APPLICATIONThe output can control high-power equipment, bulb, LED strip, DC motor, micro pump, solenoid valve, etc.
EASY INSTALLATIONThe PLC amplifier circuit board with professional design is easy to install.
9. 10Amp 7V - 30V Dual Channel DC Motor Driver Speed Controller Shield for Arduino
Feature
Arduino Shield control for two brushed DC motor from DC 7V to 30VAble to control bidirectional single bipolar/unipolar stepper motor from 7V to 30V.
Maximum Motor Current: 10A continuous, 30A peak
Buttons for quick testing and indicator LEDs for motor output state
Overcurrent protection, temperature protection and undervoltage shutdown.
10. Acxico 1Pcs Full Color RGB LED Strip Driver Module Shield for Arduino UNO R3 STM32 AVR V1.0 for 5V MCU System
Feature
Based on a P9813; Can be cascaded all lights of the drive module;Can also be cascaded more drive modules to control more light bar.Just two signal lines and two power cords can control five meters long full-color (RGB) light bar (72W Max).Just set the program of red, green and blue corresponding to that of the corresponding channel.
Widely used in guardrail control, room decor and other occasions.4 Pcs M2 screws positioning holes for easy installation.
Suitable for 5V MCU system, Arduino UNO R3 and its compatible motherboard.
Power supply of controlling interface for MCU is 4.5~5.5VDC;External power supply is 12VDC.
Recent Comments